223 subsonic with clays powder11/28/2023 ![]() If you take a full size case such as a 30-06 or 308 then you might try some 4198 or a similar burning powder such as Alliant Reloader 7. If you want to go up in power somewhat but still want a reduced load then a rifle powder that is not generally used might be the ticket. It can be used in any 30 caliber rifle with good results. A good example is a 110 gr bullet meant for a 30 carbine. All factors being equal, a light bullet produces less recoil and range then a heavier slug. Lightweight BulletsĪnother thing to reduce power along with the powder is to use a lightweight bullet. With handguns, loads can be reduced as long as they function the action. Where legal, they make fine small game loads as they don’t destroy much meat while getting the job done. Virtually all of my modern rifles has at least 1 or 2 reduced loads worked up for them. Generally, they produce excellent accuracy. In addition, cast bullets are more desirable because they are less expensive and require less pressure to push down a barrel. With magnum cases, IMR Trail Boss is the best choice as it takes up a lot of space which aids in consistency. It is an extremely consistent powder for that use. I have shot a lot of different rounds with Trail Boss and cast bullets with excellent results. It is a very low-density powder and is possibly the best powder for rifle cases and cast bullets. A powder that came out a few years ago is Trail Boss. The IMR 7 and 800 powders also work okay with reduced loads. I use such powders as Alliant Herco, Green Dot, Red Dot, and to a certain extent, Blue Dot. Flake powders in general work well with reduced loads because they are easy to ignite and take up space. I obtain excellent accuracy and it is a good way to use old cases. One of my favorites is using 10 to 12 grains of Unique Smokeless Powder with a 165-grain cast in a 30-06. Done properly it works well especially with cast bullets. ![]() The most obvious way is to use a small charge of a fast burning powder. There are several ways to accomplish this though a couple are not well known and seldom used. In fact, there are some reduced loads offered by the factories in a few of the more popular ammo rounds. That reduces the recoil and is still powerful enough to harvest deer. For example you can take a 30-06 ammunition and load it to 30-30 velocities without much problem. REDUCE RIFLE AND HANDGUN CHARGE WEIGHTS BY 10% TO ESTABLISH A STARTING LOAD.ĭO NOT EXCEED THE LOADS DISPLAYED ON THE SITE OR ALLIANT'S RELOADERS GUIDE.The most obvious is the recoil reduction that they produce. ![]() USE THIS DATA WITH ALLIANT BRAND POWDERS ONLY. The individual accessing this site assumes the risk of safe loading practices.įailure to do so could result in severe personal injury (or death) and/or property damage. Alliant Powder neither assumes nor authorizes any person to assume for it any liability in connection with the use of any product or data. Buyers and users assume all risk, responsibility and liability whatsoever for any and all injuries (including death), losses or damages to persons or property (including consequential damages), arising from the use of any product or data, whether or not occasioned by seller's negligence or based on strict liability or principles of indemnity or contribution. Never substitute any smokeless powder for Black Powder or its substitute.Īlliant Powder expressly disclaims any and all warranties with respect to any and all products sold or distributed by it, the safety or suitability thereof, or the results obtained including, without limitation, any implied warranty of merchantability or fitness for a particular purpose and/or any other warranty. ![]() Never mix any two powders regardless of type, brand, or source. This information and data may vary considerably depending on many factors, including the components used, component assembly, the type of firearm used, reloading techniques, safety precautions practiced, etc. The information displayed on this site, including ballistic data, was derived from tightly controlled laboratory conditions.
0 Comments
Leave a Reply.AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |